Meyer V-MAX 3245 Operators Especificações

OPERATION and MAINTENANCE MANUALInsist on genuine Meyer Parts & Accessories

General MaintenanceMeyer Products LLC recommends this maintenance information for regular service. Sustained heavy operation may call for more frequen

5. RUNNERS (optional)A. Inspect moldboard runners for wear and height adjustment. B. Always replace runners as soon as they start to wear through.C. A

SNOW PLOW STORAGE1. When snow plow is disconnected, disconnect lift chains from lift arm and extend lift cylinder to end of stroke and c

These charts are intended to be used as an aid in diagnosing problems on the V-68 Meyer Hydraulic Power Units. They are not a substitute for fa

-12-

-13-

-14-

-15-

-16-

-17-

Snow, despite the beauty it may impart to a bleak winter landscape, poses the dual threat of inconvenience and danger. The environmental conditi

-18-

PREPARING AREAS, USE OF GUIDE MARKERSEvery area to be plowed should be inspected before snowfall for potential hazards. Holes should be repaired, rai

Selecting EquipmentWhere you plan to plow, and the conditions under which you will be plowing, determine to a great extent the type of vehicle you’ll

Plow with the StormIt is of utmost importance to remember one basic rule — Always plow with the storm. Start plowing when snow is 1 to 4 inches deep,

These two snow plowing techniques have been time- and operation-tested. Use them as guidelines for most snow plowing strategies. Plan I is for

SNOW PLOWING OPEN AREASOpen areas such as parking lots require a more serious approach to planning, where to begin, and where snow can be stacked at t

STRAIGHT LINE SNOW PLOWINGThis method is most efficient for streets and roads. V type snowplows mounted on heavy utility vehicles or servic

CLEARING TRAPPED AREASAreas where there is little or no space for stacking cleared snow are considered “trapped.” An example is an area requiring ful

Meyer SpreadersHotshot ™(38100) &Hotshot HD™ (38110)The Meyer Hotshot spreaders promise to last season after season. These Spreaders are availabl

Under Tailgate SpreaderAn extremely rugged truck accessory, the Under-Tailgate Spreader is offered in two models: a single auger or for ultimat

Table of Contents PageGet to Know Your Meyer Plus Snow Plow 2-3Plus Specifications 4Snow Plow Operation 5Removing & Attaching Your Meyer E-Z Mo

Ice HawkThis innovative configuration comes complete with its own, built-in hydraulics system! This self-contained v-box spreader unit can b

Winch KitsE-ZMount Plus (16529)M-1 Hydraulic FluidKeep your Meyer Electro-Touch® snow plow control system operating at peak performance; change

CUTTING EDGES - (STEEL) 09218 (2) SV 8.509219 (2) SV 9.5CUTTING EDGE NUTS & BOLTS (STEEL) 21943 (10) BOLT20307 (10) LOCKNUT SNOWPLOW HARDWARE

-31-V-68 POWER UNIT PARTS 15925 S1 SOLENOID ASSY. 15917 S1 VALVE 15044 S2 SOLENOID ASSY. 15055 S2 VALVE 15926 S5 & S6 SOLENOID ASSY. 15918

Where PurchasedCompany __________________________________________City _______________________________________________State ___________________________

MEYER®/DIAMOND® SNOW PLOWSLIMITED WARRANTYcontinued from reverse sideThe original purchaser’s sole and exclusive remedy against Meyer Products LLC, an

MEYER®/DIAMOND® SNOW PLOWSLIMITED WARRANTYMeyer Products LLC warrants to the original purchaser of Meyer® and Diamond® brand products that they will b

1. Aggressor Wings, Left and Right Made from 12 gauge Steel, 4 lazer cut vertical ribs per wing.2. Cutting Edge - Reversible Replaceable high ca

-3-677891011121312345671V68

SPECIFICATIONS SV-8.5 SV-9.0WEIGHT (TOTAL) 915 lbs. 955 lbs.HEIGHT 30.5” 30.5”LENGTH 102” 114”MOLDBOARD GAUGE #12 #12VERTICAL RIBS/WING 4

-5-HAND HELD CONTROLLERThe snow plow should only be in operation when the vehicle ignition switch and the control switch are in the “ON” position. Car

Removing and Attaching Plus PlowDETACHING THE COMPLETE ASSEMBLY Leave control switch in lower float position and push down on the Lift Arm. Disconnect

Crankstand Storage To store Crankstand on the Lift Frame slide the tube that is attached to the side of the Crankstand over the receiver tube on the